Zenolite
Zenolite™ is a multi-purpose product that gives a superior high gloss glass appearance without the installation restrictions and cost of glass, or the design limitations of aluminium.
For residential and commercia as 25 times the impact strength of glass.
FEATURES
- Superior gloss surface
- Colour is integrated into the product, not a spray painted finish
- Easily fabricated with standard woodworking tools and suitable for simple thermoforming, bending and gluing (Please refer to the zenolite_technical_brochure)
- Can be utilised in retrofit door panel systems, allowing the cupboards to match or compliment the wall
- Can be used as a Marker Board (Please refer to the attached)
markerboard_flyer_final 331.51 Kb
APPLICATIONS
RESIDENTIAL
- Kitchen cabinetry and splashbacks (accompanied with a 300mm high insert stainless steel plate)
- Laundry splashbacks and cabinetry
- Living areas such as entertainment rooms
COMMERCIAL
- Office Fit outs
- Hospitality
- Hotels
- Shopfitting
LIMITATIONS
Zenolite™ is not recommended where a direct heat source is applied such as behind cook tops
To comply with Australian standards, Zenolite™ sheet must be installed with a minimum of 300mm clearance to periphery of any gas burners.
CLEANING
To clean simply use a diluted solution of non abrasive detergent and a soft cloth
To remove, use a new cloth and polish in a gentle circular motion (while still damp)
Please refer to the zenolite__polishing_guide_ for more details.
Colours
- Please click the checkbox of the sample(s) you would like to request and proceed to the bottom of the page.
- Enter your email address in the space provided and we will send your samples promptly.
Please note there is a maximum of 5 samples per order.
You may only request samples for one particular product at a time.
To order more samples of other products please repeat this process.
Request Samples
|
Standard Sheet Sizes |
||
| Width (mm) | Length (mm) | Thickness (mm) |
|
1240 |
2465 |
6 |
| 1240 |
3690 |
6 |
| Physical properties | |||||
|
Properties |
Metric US |
US |
|||
| Properties | Test | Result |
Unit |
Result |
Unit |
| Specific Gravity | ASTM D-792 |
1.19 | _ | 1.19 | |
| Water Absorption |
ASTM D-570 |
< 0.5% |
< 0.5% | ||
| Diagonal Difference | < 4 | mm | <0.16 | in | |
| Thickness | 6 | mm | 0.24 | in | |
| Tensile Strength, Max | ASTM D-638 | 70 | MPa | 10,000 | psi |
| Elongation at Break | ASTM D-638 | 4% | 4% | ||
| Tensile Modulus | ASTM D-638 | 3000 | MPa | 435,000 | psi |
| Flexural Strength | ASTM D-790 | 100 | MPa | 15,000 | psi |
| Flexural Modulus | ASTM D-790 | 3000 | MPa | 435,000 | psi |
|
Izod Impact Strength, Milled Notch |
ASTM D-256 | 15 | J/m | 0.28 | ft/lbs.in |
| Abrasion (Taber, 10 rots. CS10F 500g) | ASTM D-1044 | 11% | Haze | 11% | Haze |
| HDT, 264psi, 1.82MPa | ASTM D-648 | 96 | °C | 203 | °F |
| Specific Heat Capacity |
1.47 | J/ gK |
0.35 | BTU/lb-°F | |
| CTE, -30 to 30C |
ASTM D-696 |
7 |
mm/(mm.°C) x10 -5 |
4 |
in/(in.°F)
x10 -5 |
| Thermal Conductivity |
ASTM C-177 |
0.18 | W/mK | 1.25 | BTU-in/hr-ft2-°F |
| Continuous service temperature | 77 | °C | 170 | °F | |
| max temperature, short term |
95 | °C | 202 | °F | |
| Degradation Temperature |
> 275 |
°C | > 530 | °F | |
| Flame Spread |
ASTM E84 |
> 120 1- |
> 120 1- | ||
| Hazard Test to AS 1530.3.1999 |
|||||
| Ignitability Index (Range 0 - 20) |
13 | ||||
| Spread of Flame Index (Range 0 - 10) |
7 | ||||
| Heat Evolved index (Range 0 - 10) |
7 | ||||
| Smoke Developed Index (Range 0 - 10) |
4 | ||||
TECHNICAL
Please refer to the MSDS for more information.
CUSTOMISATION
Zenolite™ can be made to order. This means that colour choice is endless and we can match new designs or existing backgrounds on demand.
Custom sizes of up to 5000mm x 2050mm, and customised colours are available upon request and subject to minimum order quantities. Lead times are approximately 8 – 10 weeks.
Brochures
Click the brochures or samples tab of the product you would like more information about.
 |
 |
 |
 |
 |
 |
 |
 |